Please Note Anyone worldwide may purchase this FOX Racing Shox product however the delivery address must be inside the United States. Fox 32mm Float Performance 29 Fork 2017 Own The Course The 2017 Fox 32mm Performance series forks were reimagined with GRIP dampers featuring FIT sealed cartridge technology. I have a Fox Float 32 RL fork that's on a 2008 Trek EX8. 2005-2012 FLOAT & ALPS 120, 130 & 140 (O/B R, RL & RLC dampers) Since my Bike is a 2008 and the fork is a.
Fox 32 Rl
Installing Your Fork Before You Ride Setting Sag Adjusting Rebound Locking Out the Fork Service Intervals Important Safety Information
travel | 140 RL: 5.5 in./140 mm |
features/adjustments | lever-actuated lockout, air spring pressure, rebound
|
spring/damper type | air/FIT RL |
intended use | all-mountain, cross-country |
Installing Your Fork
Be sure your fork is properly installed before proceeding. If your fork came pre-installed on your bicycle, continue to the next section.
Before You Ride
- Check that quick-release levers are properly adjusted and tightened.
- Clean the outside of your fork with only mild soap and water, and wipe dry with a soft dry rag.
Note:Do not use any solvents or de-greasers, as these products can cause serious damage to paint and anodized parts (upper tubes, knobs, steerers).
Do not spray water directly on the seal/upper tube junction. Do not use a high pressure washer on your fork.
- Inspect the entire exterior of your fork. The fork should not be used if any of the exterior parts appear to be damaged. Contact your local dealer or FOX Racing Shox for further inspection and repair.
- Check your headset adjustment. If loose, adjust it accordingly to your bicycle manufacturer's recommendations.
- Check that all brake cables or hoses are properly fastened.
- Test the proper operation of your front and rear brakes on level ground.
Setting Sag
You can also view a Flash video on Setting Sag.
To get the best performance from your fork, it is necessary to set and adjust sag. Generally, sag should be set to 15 – 25% of total fork travel.
- Unscrew the blue aircap on top of the left fork leg to expose the Schrader valve.
- Attach a FOX Racing Shox High Pressure Pump to the Schrader valve.
- Pump your fork to the appropriate setting from the Suggested Air Spring Pressure Settings table below, then remove the pump.
- Unless your fork already has a sag setting o-ring on an upper tube, install a zip tie to an upper tube. Slide the o-ring or the zip tie down against the scraper lip of the fork dust seal.
- Make sure your fork lockout is not engaged.
- Dressed to ride, position your bike next to a wall or table to support yourself. Without bouncing, mount your bicycle. Assume a normal riding position for at least 30 seconds, allowing the suspension to fully settle.
- Dismount your bike without bouncing downward, without further moving the o-ring or zip tie. Measure the distance between the seal and the zip tie. This measurement is your sag value.
- Compare your actual sag value to your target sag value in the Sag Setup table below.
If your sag measurement value is less than the Sag Setup table value, screw on the pump fitting, note the current air pressure setting and depress the black bleed-valve to reduce the gauge pressure by 5 psi. Measure sag again and repeat this adjustment, if necessary.
If your sag measurement value is greater than the Sag Setup table value, screw on the pump fitting, note the current air pressure setting and pump to increase the gauge pressure by 5 psi. Measure sag again and repeat this adjustment if necessary. - Screw the blue aircap back on, and go ride.
Rider
Weight
lbs.Suggested Air Spring Pressure Settings
PSI140 mm
150 mm
≤125
45
40
125 - 135
50
45
135 - 145
55
50
145 - 155
65
60
Nov 27, 2018 This interactive map shows all marked Fallout: New Vegas locations. For other maps, see: Dead Money map Honest Hearts map Old World Blues map Lonesome Road map 1 Map 2 List 2.1 Caves and mines 2.1.1 Caves 2.1.2 Mines 2.1.3 Other 2.2 Factions 2.2.1 Boomers 2.2.2 Brotherhood of Steel (Mojave chapter) 2.2.3 Caesar's Legion 2.2.4 Fiends 2.2.5 Followers of the Apocalypse 2.2.6 Great Khans 2.2.7. Red= Primary locations Blue= Vaults Early concept of the Fallout: New Vegas map, explained by Chris Avellone during the Rezzed 2013 Developer Sessions. It features several names which were eventually cut from the game. See full list on fallout.fandom.com. See full list on fallout.gamepedia.com. Fallout new vegas vault locations map.
155 - 170
70
65
170 - 185
75
70
185 - 200
80
80
200 - 215
90
90
215 - 230
100
100
230 - ≥250
110
110
Sag Setup
Travel
XC/Race FIRM
All-Mountain PLUSH
140 mm (5.50')
21 mm (0.81')
35 mm (1.38')
150 mm (5.90')
23 mm (0.91')
38 mm (1.50')
Sag Troubleshooting
Symptom
Remedy
Too much sag
(+) air pressure in 5 psi increments
Too little sag
(-) air pressure in 5 psi increments
Excessive bottoming
(+) air pressure in 5 psi increments
Harsh ride; full travel not utilized
(-) air pressure in 5 psi increments
Fox Float Rl Shock Manual
Adjusting Rebound
The rebound adjuster knob is located at the bottom of the right fork leg. This knob has 18 clicks of potential adjustment range.
Rebound controls the rate of speed at which the fork extends after compressing. Turning the knob clockwise slows down rebound; turning the knob counter-clockwise speeds up rebound. As a starting point, turn the rebound adjuster knob all the way clockwise (full in) until it stops, then turn counter-clockwise (out) 12 clicks.
Knob Setting | Setting Description | Tuning Tips | Setup Tips |
1 | Slow Rebound | Too slow and your fork will pack down and ride harshly. | If you increase your spring rate or air pressure, you will need to slow down your rebound |
12 (Factory setting) | Average Rebound | ||
18 | Fast Rebound | Too fast and you will experience poor traction and wheel hop. | If you decrease your spring rate or air pressure, you will need to speed up your rebound setting. |
Locking Out the Fork
The blue compression lockout lever, located on the right-side top cap, allows you to close the compression damping circuit in the fork. This keeps the fork at the top of its travel, making it harder to compress.
Rotate the lever fully clockwise to lock out the fork. This position is useful in climbing and sprinting situations, but will sag with the rider’s weight. The fork will 'blowoff' in the event that a big hit is encountered with the fork locked out.
To unlock the fork, simply rotate the lever fully counter-clockwise.
Note:The fork may cycle a couple of times after enabling lockout. Once complete lockout is achieved, the fork may continue to move 3 - 5 mm. This is normal and does not affect performance.
2017 Fox 36 Rc2
Bushing Technology & InspectionSeals & Foam RingsControl DirectionOil VolumesStructural InspectionDropout Thickness InspectionTorque ValuesUnit ConversionSuspension Tuning TipsUsing the PumpImportant Safety InformationService IntervalsContact FOX ServiceWarranty InformationFOXHelp Service Web Site
Fox Float 32 Rl Rebuild
Copyright © 2011
FOX Factory Inc.